1. Welcome to Jeeps.net!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Jeep discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Jeep owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

1994 YJ build.

Discussion in 'Wrangler YJ Builds (1986-1995)' started by OFFGRID, Oct 4, 2016.

  1. Oct 4, 2016 at 9:04 AM
    #1
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    So I was running through some ads looking for parts for my CJ6 that I have plans on building when I ran across this 1994 YJ with 78000 miles. The PO decided to take the axles and cut all the brackets off in performing a SOA lift. For some reason he opened the pumpkins quit working on it and left everything open in the weather for a year. There is some rust around the wheel wells and windshield and in the open pumpkins. Just needs paint and to be put back together, so I bought it like a rescue dog to prevent it from being parted out.

    20160917_182133.jpg
     
    Last edited: Feb 9, 2017
    JKBob 25, OleMissYJ and JeepMafiaMama like this.
  2. Oct 4, 2016 at 9:13 AM
    #2
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Last week I found a set of YJ axles with 3.73 gears in them. A vast improvement over the stock 3.07 gears that came with the jeep. Now I can run 33s easily. The rear teeth are chewed up. Pinion bearing disintegrated. Probably ran it dry. Waiting on new parts to rebuild it.
     
    JKBob 25 likes this.
  3. Oct 4, 2016 at 9:41 AM
    #3
    C2T

    C2T Well-Known Member

    Joined:
    Jul 31, 2016
    Member:
    #42
    Messages:
    763
    Gender:
    Male
    First Name:
    Richard
    Helena, Montana
    Vehicle:
    Jeep
    2.5" AEV Dual Sport lift, 35" Treadwright Guard Dogs, Black Rock Wheels, AEV Front & Rear Bumpers with Tire Carrier, Fuel Caddy 10 gal. Aux. fuel tank, Warn 9.5ti, 125' synthetic winch line, front axle skid, 20" LED light bar , Bilstein Shocks, steel steering skidplate,
    Nice find.
     
    gear head girl and JKBob 25 like this.
  4. Oct 4, 2016 at 11:54 AM
    #4
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Does anyone have pictures or diagram of how the vacuum is run on the front axle of a 94yj. I've never seen such a contraption. It looks like there is a vacuum slot on the t case as well. I bought this in pieces so not exactly sure on the routing.
     
  5. Oct 4, 2016 at 12:18 PM
    #5
    VOZ

    VOZ Committed

    Joined:
    Sep 27, 2016
    Member:
    #281
    Messages:
    58
    Gender:
    Male
    Clayton, NC
    Vehicle:
    91 YJ RED
    Much
    Get rid of that thing...
    Either TJ shafts or a Posi-Lok
     
  6. Oct 4, 2016 at 12:29 PM
    #6
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Will the TJ shafts slip right in? I assume if they do just cap the axle hole with a plate where the vacuum plate is. I'm not interested in sinking a bunch of money into it. I just wanted to give it new life and back on the road. I have 2 other projects that I'm working on. This jeep just had too much to offer for me to let it be parted out.
     
    JKBob 25 likes this.
  7. Oct 4, 2016 at 3:00 PM
    #7
    VOZ

    VOZ Committed

    Joined:
    Sep 27, 2016
    Member:
    #281
    Messages:
    58
    Gender:
    Male
    Clayton, NC
    Vehicle:
    91 YJ RED
    Much
    Yes, they slip in...
    Front driveshaft will spin all the time, sometimes you get a vibration from shaft just have it balanced and all is well


    It's a Jeep sir, it takes most of your money..lol
     
    Last edited: Oct 4, 2016
    JKBob 25 and JeepMafiaMama like this.
  8. Feb 9, 2017 at 11:55 AM
    #8
    rustbucket

    rustbucket Member

    Joined:
    Feb 5, 2017
    Member:
    #920
    Messages:
    5
    Gender:
    Male
    First Name:
    Ron
    Vehicle:
    1993 YJ
    Body removed due to rust
  9. Feb 9, 2017 at 3:27 PM
    #9
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Thanks I've been looking into that. Took me 6mo to get it off the trailer. Hopefully over spring break I'll have it mechanically ready. Then the interior and paint.
     
    JKBob 25 likes this.
  10. Feb 10, 2017 at 6:49 PM
    #10
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Richard. Now I see how you know so much about the engine diagnostics. I bet you have one of these sets that I just got in the mail. Started reading powertrain diagnostic procedures. Can't wait to get started.20170210_204430.jpg
     
  11. Feb 13, 2017 at 5:33 PM
    #11
    Jeeper

    Jeeper Active Member

    Joined:
    Jan 17, 2017
    Member:
    #829
    Messages:
    25
    Gender:
    Male
    that's a great find
     
    JKBob 25 likes this.
  12. Feb 13, 2017 at 9:20 PM
    #12
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    The YJ or the manuals. I love them both.

    On another note. I have the rebuilt axles installed with 3.5in lift. Started to install the transfer case and noticed that the PO did not give me the front output yoke or the nuts to bolt to the tranny. Installed SYE kit. Ordered new windshield frame and yoke. Will take some pictures next trip to the shop and post the progress on here.
     
    JKBob 25 likes this.
  13. Feb 22, 2017 at 6:30 PM
    #13
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    It's off the trailer, axles installed, tires on it. Now I have to figure out what is wrong with this t case the po said he rebuilt. Out of the jeep I can turn the input shaft and rear axle shaft when in 2 wheel drive. In neutral the front output shaft won't make a full turn without binding. In 4x4 nothing makes a full turn without binding. Something up with the front drive output shaft or other. Figure this out, drive shafts paint and clean up the interior and I'm done. 4 in lift, sits easily on 33x12.50x15s.20170222_190829.jpg20170222_190854.jpg20170222_190918.jpg20170222_190938.jpg
     
    JKBob 25 likes this.
  14. Apr 7, 2017 at 7:42 PM
    #14
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    20170407_212602.jpg 20170407_212552.jpg 20170407_212520.jpg 20170407_212506.jpg 20170407_212439.jpg Rebuilt axles 3.73 gears up from 3.07. Rebuilt t case with sye, New Tom Woods shafts with double cardan in back. 4 in lift. All fluids changed. Needs paint and body and interior cleaned up and it's done
     
    JKBob 25 and chris4x4 like this.
  15. Apr 29, 2017 at 7:47 PM
    #15
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    20170427_160047_1493326903820.jpg 20170428_093444_1493390093287.jpg 20170428_091940_1493389202126.jpg 20170428_113931_1493397584954.jpg 20170428_121825_1493399914132.jpg

    20170428_113924_1493397594369.jpg
     
    JKBob 25 likes this.
  16. Apr 29, 2017 at 7:53 PM
    #16
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Dang I am so glad that my friend George Cordero at G&S Autoworks is such a good friend. He has agreed to paint the YJ for me. After a few knocks with a hammer on some suspected bondo patches that the POs have done he said I'm really going to owe him. Ordered some new body panels because he didn't have enough spare sheet metal lying around to finish the job.
     
    Bob likes this.
  17. May 4, 2017 at 11:18 AM
    #17
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Amazing what you can do with a hammer and some tinsnips.

    20170501_115613_1493658882979.jpg 20170501_121429_1493658891231.jpg
     
    JKBob 25 likes this.
  18. May 4, 2017 at 11:23 AM
    #18
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Primed and ready for paint.

    20170504_114714_1493916524210.jpg 20170504_114723_1493916516282.jpg 20170504_114734_1493916507550.jpg 20170504_114744_1493916484661.jpg
     
  19. May 8, 2017 at 8:29 PM
    #19
    JKBob 25

    JKBob 25 Well-Known Member

    Joined:
    Mar 22, 2017
    Member:
    #1197
    Messages:
    3,874
    Gender:
    Male
    First Name:
    Bob
    Jersey Shore, NJ
    Vehicle:
    2016 JK Wrangler Sport
    Waz just lookin over some threads on other Jeeps. Saw this one. Brought to mind some thing my Mom said not to long ago. Why do you guys replaced the tires and rims first.

    My Dad passed just over 3 years ago. He picked up a 1951 Ford pickup he was planning on rebuilding. And the first thing he did was replaced the tires and wheels. I tried to explain it's a Guy thing. We want nice tires and wheels.

    Your build is coming along awesome dude. I'm subscribed. I'LL be checking back. Post more pics dude. It's a Jeep thing.
     
    gear head girl likes this.
  20. May 9, 2017 at 6:00 AM
    #20
    OFFGRID

    OFFGRID [OP] Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    For me 2 of the old tires would not hold air, so it was a necessity thing. I have a hookup at Discount Tire so rather than waste money on trying to repair dryrotted tires I got these for under $500, but yeah New tires turns a hoopty into a nice ride.
     
    JKBob 25 likes this.
To Top