1. Welcome to Jeeps.net!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Jeep discussion topics
    • Communicate privately with other Jeep owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

4 cylinder to 6 cylinder swap

Discussion in 'Wrangler YJ (1986-1995)' started by jeepguy87, Jan 30, 2017.

  1. Jan 30, 2017 at 5:14 PM
    #1
    jeepguy87

    jeepguy87 [OP] New Member

    Joined:
    Jan 30, 2017
    Member:
    #896
    Messages:
    4
    Gender:
    Male
    Vehicle:
    1993 white Wrangler yj
    I have a 93 Wrangler yj with a 4 cylinder and I need a new transmission. So I was thinking of an engine upgrade when I get new tranny but what tranny fits a 4.0 6 cylinder?
     
  2. Jan 30, 2017 at 5:58 PM
    #2
    C2T

    C2T Well-Known Member

    Joined:
    Jul 31, 2016
    Member:
    #42
    Messages:
    759
    Gender:
    Male
    First Name:
    Richard
    Helena, Montana
    Vehicle:
    Jeep
    2.5" AEV Dual Sport lift, 35" Treadwright Guard Dogs, Black Rock Wheels, AEV Front & Rear Bumpers with Tire Carrier, Fuel Caddy 10 gal. Aux. fuel tank, Warn 9.5ti, 125' synthetic winch line, front axle skid, 20" LED light bar , Bilstein Shocks, steel steering skidplate,
    AX15 But you will likely need to change the transfer case too.
     
    jeepguy87 [OP] likes this.
  3. Jan 30, 2017 at 7:14 PM
    #3
    jeepguy87

    jeepguy87 [OP] New Member

    Joined:
    Jan 30, 2017
    Member:
    #896
    Messages:
    4
    Gender:
    Male
    Vehicle:
    1993 white Wrangler yj
    I will do that thank you.
     
  4. Jan 30, 2017 at 8:25 PM
    #4
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    1,752
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    I say go find you a wrecked YJ or someone who is parting it out and buy the whole setup for under $1K. I bet if you look hard enough you could find it all (engine, tranny, and Tcase) for close to $500. You may also need driveshafts, so grab those too from whoever you buy the package from. You could even switch to an automatic if you want since youre doing the switch. I see lots of fun in your near future!
     
    jeepguy87 [OP] likes this.
To Top