1. Welcome to Jeeps.net!

    You are currently viewing as a guest! To get full-access, you need to register for a FREE account.

    As a registered member, you’ll be able to:
    • Participate in all Jeep discussion topics
    • Transfer over your build thread from a different forum to this one
    • Communicate privately with other Jeep owners from around the world
    • Post your own photos in our Members Gallery
    • Access all special features of the site

Do I have a bad PCM?

Discussion in 'Cherokee' started by zancudo, Nov 9, 2016.

  1. Nov 9, 2016 at 7:06 PM
    #1
    zancudo

    zancudo [OP] New Member

    Joined:
    Nov 9, 2016
    Member:
    #473
    Messages:
    3
    Gender:
    Male
    First Name:
    efren
    Vehicle:
    2001 jeep cherokee 4.0
    OK so i need your help. My 2001 Jeep Cherokee 4.0 was stalling a little so I connected a scanner and got a code telling me I had a cylinder #4 misfire. So i went ahead and replaced the spark plugs and the coil pack, turned on the Jeep and it's still stalling. So i hooked up the scanner again and the missfire code was gone but now i have a #2 injector open circuit. I've checked for a short ground on the wiring but found nothing and there's no ground to the injector.
     
  2. Nov 10, 2016 at 6:06 AM
    #2
    chris4x4

    chris4x4 With sufficient thrust, pigs fly just fine Moderator

    Joined:
    Jul 19, 2016
    Member:
    #2
    Messages:
    4,068
    Gender:
    Male
    I thought the PCM being bad would throw a different code?
     
  3. Nov 10, 2016 at 10:25 AM
    #3
    zancudo

    zancudo [OP] New Member

    Joined:
    Nov 9, 2016
    Member:
    #473
    Messages:
    3
    Gender:
    Male
    First Name:
    efren
    Vehicle:
    2001 jeep cherokee 4.0
    as i was reading on other threads i might have a bad in my pcm so i dont really know if the conputer is bad or its something about a sensor
     
  4. Nov 14, 2016 at 8:34 PM
    #4
    C2T

    C2T Well-Known Member

    Joined:
    Jul 31, 2016
    Member:
    #42
    Messages:
    763
    Gender:
    Male
    First Name:
    Richard
    Helena, Montana
    Vehicle:
    Jeep
    2.5" AEV Dual Sport lift, 35" Treadwright Guard Dogs, Black Rock Wheels, AEV Front & Rear Bumpers with Tire Carrier, Fuel Caddy 10 gal. Aux. fuel tank, Warn 9.5ti, 125' synthetic winch line, front axle skid, 20" LED light bar , Bilstein Shocks, steel steering skidplate,
    Of course, double check your connections. Switch around the erroring injector and a good one and see if the issue moves with the injector. If it does, replace the injector. If it stays in the same place, look at wiring.

    In answer to your question, a PCM is possible but I think it unlikely.
     
    Last edited: Nov 14, 2016
  5. Nov 16, 2016 at 4:51 AM
    #5
    zancudo

    zancudo [OP] New Member

    Joined:
    Nov 9, 2016
    Member:
    #473
    Messages:
    3
    Gender:
    Male
    First Name:
    efren
    Vehicle:
    2001 jeep cherokee 4.0
    i swap the injetor 3 to 2 and the probem stayed and the code didnt change i have check the wiring from the pcm to the imjector conector and seems to be fine i just ordered a reman ecm hope that solve my problem
     
  6. May 15, 2017 at 8:26 AM
    #6
    OFFGRID

    OFFGRID Well-Known Member

    Joined:
    Oct 3, 2016
    Member:
    #317
    Messages:
    2,018
    Gender:
    Male
    First Name:
    Peter
    Houston
    Vehicle:
    1979 Jeep CJ7, 258, TH350, NP208
    Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37" Toyo MTs.
    Did you fix your problem? I was reading and found others with your same problem, and did the same things you did to try to fix it. They ended up replacing the injector on the misfiring cylinder and it fixed the problem.
     

Products Discussed in

To Top